{
    "type": "filament",
    "name": "Lofted Aero Tuned Generic Foaming LW-PLA",
    "from": "User",
    "instantiation": "true",
    "inherits": "",
    "version": "1.9.0.0",
    "filament_settings_id": [
        "Lofted Aero Tuned Generic Foaming LW-PLA"
    ],
    "filament_notes": "Lofted Aero Tune v1.0 | 2026-07-26 | For active-foaming lightweight PLA from any vendor - 3D LabPrint LW-PLA, ColorFabb LW-PLA and equivalents. Flow ratio 0.5 assumes ~2x foaming expansion at 238 C. NON-BAMBU PRINTERS: clear the filament start G-code below, the M106 P3 line drives the Bambu auxiliary fan. | loftedaero.com",

    "compatible_printers": [],
    "compatible_printers_condition": "",
    "compatible_prints": [],
    "compatible_prints_condition": "",

    "filament_type": [
        "PLA"
    ],
    "filament_vendor": [
        "Generic"
    ],
    "filament_density": [
        "1.14"
    ],
    "filament_cost": [
        "29"
    ],
    "filament_diameter": [
        "1.75"
    ],
    "filament_soluble": [
        "0"
    ],
    "filament_is_support": [
        "0"
    ],
    "filament_shrink": [
        "100%"
    ],
    "temperature_vitrification": [
        "45"
    ],
    "required_nozzle_HRC": [
        "0"
    ],

    "nozzle_temperature": [
        "238"
    ],
    "nozzle_temperature_initial_layer": [
        "238"
    ],
    "nozzle_temperature_range_low": [
        "190"
    ],
    "nozzle_temperature_range_high": [
        "260"
    ],

    "cool_plate_temp": [
        "35"
    ],
    "cool_plate_temp_initial_layer": [
        "35"
    ],
    "eng_plate_temp": [
        "45"
    ],
    "eng_plate_temp_initial_layer": [
        "45"
    ],
    "textured_plate_temp": [
        "45"
    ],
    "textured_plate_temp_initial_layer": [
        "45"
    ],
    "hot_plate_temp": [
        "56"
    ],
    "hot_plate_temp_initial_layer": [
        "56"
    ],

    "filament_flow_ratio": [
        "0.5"
    ],
    "filament_max_volumetric_speed": [
        "5"
    ],
    "enable_pressure_advance": [
        "0"
    ],
    "pressure_advance": [
        "0.02"
    ],

    "counter_coef_1": [
        "0"
    ],
    "counter_coef_2": [
        "0.025"
    ],
    "counter_coef_3": [
        "-0.11"
    ],
    "counter_limit_max": [
        "0.05"
    ],
    "counter_limit_min": [
        "-0.04"
    ],
    "hole_coef_1": [
        "0"
    ],
    "hole_coef_2": [
        "-0.025"
    ],
    "hole_coef_3": [
        "0.28"
    ],
    "hole_limit_max": [
        "0.25"
    ],
    "hole_limit_min": [
        "0.08"
    ],

    "filament_enable_overhang_speed": [
        "1"
    ],
    "filament_overhang_1_4_speed": [
        "0"
    ],
    "filament_overhang_2_4_speed": [
        "0"
    ],
    "filament_overhang_3_4_speed": [
        "0"
    ],
    "filament_overhang_4_4_speed": [
        "0"
    ],
    "filament_overhang_totally_speed": [
        "10"
    ],

    "filament_retraction_length": [
        "0.01"
    ],
    "filament_retraction_speed": [
        "30"
    ],
    "filament_deretraction_speed": [
        "30"
    ],
    "filament_retract_restart_extra": [
        "0.12"
    ],
    "filament_retract_before_wipe": [
        "50%"
    ],
    "filament_retract_when_changing_layer": [
        "0"
    ],
    "filament_wipe": [
        "0"
    ],
    "filament_wipe_distance": [
        "2"
    ],
    "filament_z_hop": [
        "0"
    ],
    "filament_z_hop_types": [
        "Normal Lift"
    ],

    "fan_min_speed": [
        "20"
    ],
    "fan_max_speed": [
        "20"
    ],
    "fan_cooling_layer_time": [
        "60"
    ],
    "close_fan_the_first_x_layers": [
        "1"
    ],
    "full_fan_speed_layer": [
        "4"
    ],
    "additional_cooling_fan_speed": [
        "0"
    ],
    "reduce_fan_stop_start_freq": [
        "0"
    ],
    "slow_down_for_layer_cooling": [
        "0"
    ],
    "slow_down_layer_time": [
        "10"
    ],
    "slow_down_min_speed": [
        "15"
    ],
    "enable_overhang_bridge_fan": [
        "1"
    ],
    "overhang_fan_speed": [
        "50"
    ],
    "overhang_fan_threshold": [
        "95%"
    ],

    "activate_air_filtration": [
        "0"
    ],
    "during_print_exhaust_fan_speed": [
        "70"
    ],
    "complete_print_exhaust_fan_speed": [
        "70"
    ],

    "filament_start_gcode": [
        "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}"
    ],
    "filament_end_gcode": [
        "; filament end gcode\nM106 P3 S0\n"
    ]
}