{
    "activate_air_filtration": [
        "1"
    ],
    "activate_chamber_temp_control": [
        "1"
    ],
    "additional_cooling_fan_speed": [
        "0"
    ],
    "chamber_temperature": [
        "60"
    ],
    "chamber_temperatures": [
        "60"
    ],
    "close_fan_the_first_x_layers": [
        "1"
    ],
    "compatible_printers": [],
    "compatible_printers_condition": "",
    "compatible_prints": [],
    "compatible_prints_condition": "",
    "complete_print_exhaust_fan_speed": [
        "0"
    ],
    "cool_plate_temp": [
        "0"
    ],
    "cool_plate_temp_initial_layer": [
        "0"
    ],
    "during_print_exhaust_fan_speed": [
        "70"
    ],
    "enable_overhang_bridge_fan": [
        "1"
    ],
    "eng_plate_temp": [
        "90"
    ],
    "eng_plate_temp_initial_layer": [
        "90"
    ],
    "fan_cooling_layer_time": [
        "10"
    ],
    "fan_max_speed": [
        "25"
    ],
    "fan_min_speed": [
        "10"
    ],
    "filament_cost": [
        "49.99"
    ],
    "filament_density": [
        "1.047"
    ],
    "filament_diameter": [
        "1.75"
    ],
    "filament_end_gcode": [
        "; filament end gcode\n"
    ],
    "filament_flow_ratio": [
        "0.5"
    ],
    "filament_is_support": [
        "0"
    ],
    "filament_max_volumetric_speed": [
        "6"
    ],
    "filament_notes": "Lofted Aero Tune v1.0 | 2026-07-26 | For ColorFabb LW-ASA (active-foaming lightweight ASA). Foams at 255 C; flow ratio 0.5 assumes ~2x expansion. Chamber target is 60 C but active chamber heating is left OFF so the profile cannot stall an unheated printer waiting on M191 - enclosed-printer owners should turn 'activate chamber temperature control' on. Retraction is longer than the Bambu ASA Aero profile on purpose - this is an actively foaming material, not a pre-compounded one. | loftedaero.com",
    "filament_retract_before_wipe": [
        "50%"
    ],
    "filament_retract_restart_extra": [
        "0.12"
    ],
    "filament_retraction_length": [
        "1"
    ],
    "filament_settings_id": [
        "Lofted Aero Tuned ColorFabb LW-ASA"
    ],
    "filament_shrink": [
        "100%"
    ],
    "filament_soluble": [
        "0"
    ],
    "filament_start_gcode": [
        "; filament start gcode\n"
    ],
    "filament_type": [
        "ASA"
    ],
    "filament_vendor": [
        "ColorFabb"
    ],
    "filament_wipe_distance": [
        "2"
    ],
    "filament_z_hop": [
        "0"
    ],
    "filament_z_hop_types": [
        "Normal Lift"
    ],
    "from": "User",
    "full_fan_speed_layer": [
        "0"
    ],
    "hot_plate_temp": [
        "90"
    ],
    "hot_plate_temp_initial_layer": [
        "90"
    ],
    "inherits": "",
    "instantiation": "true",
    "name": "Lofted Aero Tuned ColorFabb LW-ASA",
    "nozzle_temperature": [
        "255"
    ],
    "nozzle_temperature_initial_layer": [
        "255"
    ],
    "nozzle_temperature_range_high": [
        "280"
    ],
    "nozzle_temperature_range_low": [
        "240"
    ],
    "overhang_fan_speed": [
        "50"
    ],
    "overhang_fan_threshold": [
        "25%"
    ],
    "reduce_fan_stop_start_freq": [
        "1"
    ],
    "required_nozzle_HRC": [
        "3"
    ],
    "slow_down_for_layer_cooling": [
        "1"
    ],
    "slow_down_layer_time": [
        "5"
    ],
    "slow_down_min_speed": [
        "20"
    ],
    "temperature_vitrification": [
        "100"
    ],
    "textured_plate_temp": [
        "90"
    ],
    "textured_plate_temp_initial_layer": [
        "90"
    ],
    "type": "filament",
    "version": "1.9.0.0"
}